Joined in 2023 
82 
63 About this deal
SW or AG grades and is not suitable for laminating sheets. Typical bond strengths are 24 MPa for a cold The bonds obtained using Tensol 70 are of approximately the same strength as the acrylic sheet. Typical Tensol 12 is designed for the bonding of cast acrylic sheet intended for interior use only. Extruded acrylic Tensol 12 is almost water thin so is easy to apply to VERY CLOSE FITTING parts. Capillary action draws it in to the joint. My first attempt was a bit clumsy but the plastic syringe made application straightforward. Our Trade Counter is open from 8am until 4pm Monday to Thursday and 8am until 3pm on Fridays.We are closed on weekends and bank holidays.
Tensol 12 will last for at least 12 months from date of manufacture - when stored under the above conditions. Preparation advice Alternative to Tensol 70. Indasol 7070 Structural Plastic Welder is a two component structural acrylic adhesive designed to bond cast acrylic sheet with a bond strength that should always outperform the substrate. Indasol 7070 Product DetailsTensol 70 is a two component, acrylic adhesive which hardens at room temperature by the polymerisation Joints will be hardened after about 3 hours at room temperature; but, should not be machined for at least 24 hours. The bonds will reach their maximum strength after approx. 3 weeks at room temperature; however, for most applications 1 - 2 weeks should be adequate. Cover the container and allow the mixed adhesive to stand for 5 minutes to allow the larger air bubbles to applying the adhesive and assembling the parts. Dispense the adhesive from a small polythene bottle
Thoroughly mix the adhesive by stirring, taking care to entrap as little air in the adhesive as possible. The Installation.If required please get in touch about our installation services and how we can best support you, all with a smile! EVO-PLAS TENSOL 12 is not recommended for laminating 'Perspex' sheets, as the absorption of the solvent is likely cause distortions and/or stress crazing.
How to use Tensol 12
Tensol 12 has no filling capability so would not be suitable for joints that have large gaps or where the finish is rough. In those situations something with body like an epoxy might be better. Read full review ANGLOSOL CEMENT 1200 is a ready-mixed, colourless, solvent based cement.It consists of acrylic polymer and methyl methacrylate monomer dissolved in solvents. Dispense the cement directly into the joint, using a small flexible polythene bottle with a suitable nozzle or a hypodermic syringe. This should have a wide-bore needle. Tensol 70 is designed for bonding cast acrylic sheet. It will also bond extruded acrylic sheet, but will cause Fast Bonding Clear Acrylic Adhesive. Tensol 12 is for internal plastic bonding. Tensol 12 is a single component cement which hardens due to solvent evaporation to produce a clear bond in cast acrylic sheets. Tensol 12 Product Details Tensol 70
The adhesive will be hardened sufficiently within one and a half hours to allow careful handling of the Once the adhesive has set the final bond strength can be increased by heat curing the material. This can EVO-PLAS TENSOL 12 has been specially developed to reduce the problems of rapid drying and 'skinning' common with solvent based cements. It is a versatile product for general fabrication work that does not need high bond strength. Refrigerate the cement for at least 12 hours before use. A domestic refrigerator is suitable (5 - 10�C). If this is not possible, an alternative is to cool the cement containers in cold water - although this is less effective.I intend making quite a few more enclosures for projects using a laser cutter in our MakerSpace so will use this method to assemble the parts. So far (still early days) the joints do seem to be stron g. Overall a better way to make project boxes than 3D printing. edge to face the edge should have a 10o chamfer to allow a sufficient quantity of adhesive into the joint. Surface preparation is paramount for achieving the required bond when using this pressure sensitive adhesive. Read our Surface Preparation and Application Guide for more information. Not sure if Tensol 12 is right for your requirements? Anglosol Cement 1200 is suitable for joining items made from ‘Diakon’ acrylic polymers as well as cast acrylic (Perspex). It is versatile, single part cement suitable for general fabrication work which does not need high bond strength, (usually for internal applications).
Please store Tensol 12 in a dry area in the temperature range of: 5�C - 30�C. Shelf life information assembly. After 4 hours cure the parts can be lightly machined but, for the best results, the joint should be Whether your application is seen as General Purpose or High Tech, we have a product to meet your needs. Tensol 12 I had some laser cut boxes that I needed to 'glue' together so I researched the best materials to use on acrylic. Tensol 12 is not something I knew about but it was recommended as a good way of welding the acrylic together.Known as Superglue, an economical fast bond to many surfaces and ideal for use on PVC profiles, Wood, Metal and Plastics. We also supply these products in kit form (adhesive and activator) called MITRE KITS. Cyanocrylate Product Details Fusion – Acrylic Rapid Bonding Liquid applications, 1 to 2 weeks should be adequate. To obtain the maximum strength more rapidly the bond can of the Part A. The Part A is a viscous mixture of acrylic polymer dissolved in monomer. The Part B is a Fast Bonding Clear Acrylic Adhesive. Tensol 70 is a structural version and is ideal for external use. Tensol 70 2-Part Acrylic Cement is a two-part catalyst cement which cures at ambient temperatures to produce high strength bonds with acrylic sheet and offers excellent weathering resistance. Tensol 70 Product Details Indasol 1212 shrinks on curing allowance must be made for this when making butt joints and fillet joints. When bonding
Great Deal 
New Comment